f)f> (J A L [MINING. carried above it in one of the upper beds called the slipper coal From the gate road a heading called a bolt-hole is opened, and extended into a large rectangular chamber, known as a " side of work," large pillars being left at regular Fro. 11. South Staffordshire method of working Thick Coal. intervals, besides smaller ones or cogs. The order in which the coal is cut is shown in the dotted and numbered squares in the figure. The coal is first cut to the top of the slipper coal from below, after which the upper portion is either broken down by wedging or falls of itself. The working of these upper portions is exceedingly dangerous, owing to the great height of ths excavations, and fatal accidents from falls of roof are in consequence more common in South Staffordshire than in any other coal-field in this country. The air from the down-cast shaft enters from the gate road, and passes to the up-cast through the air heading above. About one-half of the total coal (or less) is obtained in the first working ; the roof is then allowed to fall, and when the gob is sufficiently consolidated, fresh roads are driven through it to obtain the ribs and pillars left behind by a second or even, in some cases,. a third working. The loss of coal by this method is very considerable, besides great risk to life and danger from fire. It has, therefore, been to some extent superseded by the long-wall method, the upper half being taken at the first working, and removed as completely as possible, working backwards from the bound aries to the shaft. The lower half is then taken in the same manner, after the fallen roof has become sufficiently consolidated to allow the mine to be re-opened. In the working of thick seams inclined at a high angle, such as those in the south of France, and in the lignite mines of Styria and Bohemia, the method of working in horizontal slices, about 12 or 15 feet thick, and filling up the excavation with broken rock and earth from the sur face, is now generally adopted in preference to the systems formerly used. At Monceaux les Mines, in France, a seam 40 fe<:t thick, and dipping at an angle of 20 degrees, is worked in the following manner. A level is driven in a sandstone forming the floor, along the course of the coal, into which communications are made by cross cuts at intervals of 16 yards, which are driven across to the roof, dividing up the area to be worked into panels- These are worked backwards, the coal being taken to a height of 20 feet, the opening being packed up with stone sent down from the surface. As each stage is worked out, the floor level is connected with that next below it by means of an incline, which facilitates the introduction of the packing material. Stuff containing a considerable amount of clay is found to be the best suited for the purpose of filling, at it consolidates readily under pressure The actual cutting of the coal is chiefly performed by Method manual labour, the tool employed being a sharp-pointed of cutti double-armed pick, which is nearly straight, except when required for use in hard rock, when the arms are made with an inclination or " anchored." The terms pike, pick, mandril, and slitter are applied to the collier s pick in different districts, the men being known as pikemen or hewers. In driving levels it is necessary to cut grooves vertically parallel to the walls, a process known as shearing; but the most important operation is that known as holing or kirving, which consists in cutting a notch or groove in the floor of the seam to a depth of about 3 feet, measured back from the face, so as to leave the overhanging part unsupported, which then either falls of its own accord within a few hours, or is brought down either by driving wedges along the top, or by blasting with gunpowder. The process of holing in coal is one of the severest kinds of human labour. It has to be performed in a constrained posi tion, and the miner lying on his side has to cut to a much greater height, in order to get room to carry the groove in to a sufficient depth, than is required to bring the coal down, giving rise to a great waste in slack as compared with machine work. This is sometimes obviated by holing in the beds below the coal, or in any portion of a seam of inferior quality that may not be worth working. This loss is proportionately greater in thin than in thick seams, the same quantity being cut to waste in either case. The method of cutting coal on the long- wall system is seen in fig. 1 2, repre- Fio. 12. Long- wall working-face Plan and Section. senting the working at the Shipley colliery. The coal is 40 inches thick, with a seam of fire-clay and a roof of black shale , about 6 inches of the upper part, known as the roof coal, not being worth working, is left behind. A groove of triangular section of 30 inches base and 9 inches high is cut along the face, inclined timber props being placed at inter vals to support the overhanging portion until the required length is cut. These are then removed, and the coal is allowed to fall, wedges or blasting being employed when necessary. The roof of the excavation is supported as the coal is removed, by packing up the waste material, and by
a double row of props, two feet from each other, placed tem-